MOF100 1301

MOF100 1301

MOF 100 is an R/W Mono-Block allowing to exchange data with tags TAI or TAM without contact,using a protocol compliant with the standards ISO 18000-3 mode 1 & ISO 15693.
Available messaging instructions: Modbus ® / Jbus ® .

The R/W Mono-Block meets the food processing requirements:
• housing quality white polypropylene fiber reinforced food 30%
• connector IP69K stainless steel
• Stainless steel fastener insert
• To prevent food contamination the case identifier is engraved

Note:
MOF100 M 232 1301, with an RS-232 interface.  
MOF100 M 485 1301, with an RS-485 interface.  

 

Sizes (lxwxh):
120mm x 80mm x 40mm.
120mm x 96mm x 40mm, connecteur included.

 

Software: 

Compatible product(s)

Tag

TAI50 IC SLI

Radiofrequency tag, made up of an electronic chip and an antenna.

  • Based on ISO 15693 / 18000-3 Mode 1 standard
  • Data is addressed in blocks of 4 bytes
  • Memory of 112 bytes of user data + UID
  • Passive (no power source embedded).

TAI20 2K FRAM

Radiofrequency tag, made up of an electronic chip and an antenna.

  • Based on ISO 15693 / 18000-3 Mode 1 standard
  • Data is addressed in blocks of 8 bytes
  • Memory of 2000 bytes of user data + UID
  • Passive (no power source embedded)

TAI711 IC SLI

Radiofrequency tags, made up of an electronic chip and an antenna.

  • Based on ISO 15693 / 18000-3 Mode 1 standard
  • Data is addressed in blocks of 4 bytes
  • Memory of 112 bytes of user data + UID
  • Passive (no power source embedded).

Interface

BIDP170

It handles up to two independent R/W channels (both simultaneously read / write data from / to Balogh tags);
the channels may differ from each other in tags type.

Authorized slave interface for ProfiBus® DP-V1: version BIDP170 M
Authorized slave interface for ProfiBus® DP-V0: version BIDP170

CEPR96

The CEPR 96/24 is a Eurocard-format programmable board featuring:

  • one channel to control a Balogh transceiver intended for reading/writing data from/to OMA, OMX, TAI, TAM, tags,
  • 16 parallel led-indicated and isolated inputs (green leds),
  • 16 parallel led-indicated outputs (red leds) isolated and protected against short circuits,
  • one serial RS-422/RS-485 interface (or RS-232-like: V24 at levels 0 and 5 VDC),
  • one serial RS-232 interface (V24 at levels -3 ... -12 and +3 ...+12 VDC),
  • six user-definable switches.

Both serial interfaces support the JBUS ®, UNITELWAY ®, 3964R ®, DF1 ® protocols.
The software is stored in a battery-backed RAM; programming by using the ST .LAD PC software.

BIET170

Slave interface handling 2 independent R/W channels.
Exchanges occur over an Ethernet link (baud rate: 10 /100 Mbauds with autobaud).

Protocols:
BIET 170 supports several DIP-switch selectable messaging protocols:

  • TCP/IP + specialty protocol which services simultaneous 8-Kbyte requests on both channels,
  • MODBUS/TCP ® which enables to read (resp. write) 125 (resp.120) words per request,
  • EtherNet/IP ® (Allen Bradley - Rockwell).

The data for this website are not contractual - The reuse of content (text, data, picture, etc..) Is prohibited without the written agreement from Balogh.